Publicaciones en las que colabora con JOAN ROCA ENRICH (20)

2019

  1. Development of an easily adaptable three-point hitch dynamometer for agricultural tractors. Analysis of the disruptive effects on the measurements

    Soil and Tillage Research, Vol. 194

2018

  1. Efficiency analysis of a multiple axle vehicle with hydrostatic transmission overcoming obstacles

    Vehicle System Dynamics, Vol. 56, Núm. 1, pp. 55-77

  2. Surgical dynamometer to simultaneously measure the tension forces and the distance between wound edges during the closure of a laparotomy

    Sensors (Switzerland), Vol. 18, Núm. 1

2014

  1. Influence of the transmission configuration of a multiple axle vehicle on the obstacle surmounting capacity

    Vehicle System Dynamics, Vol. 52, Núm. 9, pp. 1191-1210

2013

  1. Efficiency sensitivity analysis of a hydrostatic transmission for an off-road multiple axle vehicle

    International Journal of Automotive Technology, Vol. 14, Núm. 1, pp. 151-161

2012

  1. Active bogies and chassis levelling for a vehicle operating in rough terrain

    Journal of Terramechanics, Vol. 49, Núm. 3-4, pp. 161-171

  2. Analysis of a hydrostatic transmission driveline for its use in off-road multiple axle vehicles

    Journal of Terramechanics, Vol. 49, Núm. 5, pp. 245-254

2011

  1. Comparison of different bogie configurations for a vehicle operating in rough terrain

    Journal of Terramechanics, Vol. 48, Núm. 1, pp. 75-84

2009

  1. Experimental evaluation of commercial heat exchangers for use as PCM thermal storage systems

    Applied Energy, Vol. 86, Núm. 10, pp. 2047-2055

2007

  1. Use of alternative energy sources in tanneries

    Journal of the Society of Leather Technologists and Chemists, Vol. 91, Núm. 3, pp. 93-101

  2. Use of microencapsulated phase change materials in building applications

    Thermal Performance of the Exterior Envelopes of Whole Buildings

2006

  1. Experimentation with a water tank including a PCM module

    Solar Energy Materials and Solar Cells, Vol. 90, Núm. 9, pp. 1273-1282

  2. Modelization of a water tank including a PCM module

    Applied Thermal Engineering, Vol. 26, Núm. 11-12, pp. 1328-1333

  3. Use of phase-change materials in solar domestic hot water tanks

    ASHRAE Transactions

2005

  1. Design, dynamic simulation and experimental tests of leg mechanism and driving system for a hexapod walking robot

    CLIMBING AND WALKING ROBOTS

  2. Diseño de un encapsulador plástico para PCM (phase change material) en edificios

    IV Jornadas Nacionales de Ingeniería Termodinámica: Logroño, 2 y 3 de junio de 2005. Ponencias

  3. Diseño y construcción de un sistema de aire acondicionado para realizar prácticas

    IV Jornadas Nacionales de Ingeniería Termodinámica: Logroño, 2 y 3 de junio de 2005. Ponencias

  4. Diseño y validación de un depósito de ACS con módulos de materiales de cambio de fase (PCM) en su interior con "TRNSYS"

    IV Jornadas Nacionales de Ingeniería Termodinámica: Logroño, 2 y 3 de junio de 2005. Ponencias

  5. Modelización y análisis de dos cubículos construidos en la localidad de Puigverd de Lleida (Lleida) mediante "TRNSYS"

    IV Jornadas Nacionales de Ingeniería Termodinámica: Logroño, 2 y 3 de junio de 2005. Ponencias

2002

  1. Immersion corrosion tests on metal-salt hydrate pairs used for latent heat storage in the 48 to 58 C° temperature range

    Materials and Corrosion, Vol. 53, Núm. 12, pp. 902-907